20 Pieces Micro JST PH 2.0 2-Pin Connector Plug Male and 20 Pieces 10 cm Red and Black Silicone Cable Wire with Female Connector

Product Information

A short length of pipe having an MIP thread at both ends is sometimes called a nipple. A short pipe fitting having an FIP thread at both ends is sometimes called a coupling.

The M12 connector, specified in IEC 61076-2-101, is a circular electrical plug/receptacle pair with 12mm OD mating threads, used in NMEA 2000, DeviceNet, IO-Link, some kinds of Industrial Ethernet, etc. [16] [17] Mroczkowski, Dr. Robert S. (15 October 2004). "A Perspective on Connector Reliability" (PDF). IEEE. connNtext . Retrieved 1 July 2019.In plumbing fittings, the "M" or "F" usually comes at the beginning rather than the end of the abbreviated designation. For example: Normalized failure mode distributions were originally compiled from a combination of: MIL-HDBK-978, “NASA Parts Application Handbook”, 1991; MIL-HDBK-338, “Electronic Reliability Design Handbook”, 1994; “Reliability Toolkit: Commercial Practices Edition", Reliability Analysis Center (RAC), 1998; and “Failure Mode, Effects, and Criticality Analysis (FMECA)”, RAC, 1993.

In the absence of genderless connectors, gender changer fittings might be used to enable certain connections. The designer of a connection system may use one or both schemes to allow arbitrary connectivity, or even combine both schemes into a single system. Endres, Herbert (19 December 2011). "Gold or Tin versus Gold and Tin?". Molex . Retrieved 1 July 2019. It is usually desirable for a connector to be easy to identify visually, rapid to assemble, inexpensive, and require only simple tooling. In some cases an equipment manufacturer might choose a connector specifically because it is not compatible with those from other sources, allowing control of what may be connected. No single connector has all the ideal properties for every application; the proliferation of types is a result of the diverse yet specific requirements of manufacturers. [7] :6 Materials [ edit ] Similarly, an exposed connection on a jumper cable for a 12V automotive battery can be hazardous, because of the potentially high current and energy involved. Accidental shorting of the wire to vehicle ground can cause sparks, rapid heating, or even a battery explosion.Foreman, Chris, "Sound System Design", Handbook for Sound Engineers, Third Edition, Glen M. Ballou, Ed., Elsevier Inc., 2002, pp.1171–72. If the furrowed surface be convex, 'tis called a Male Screw; if concave, a Female; and where Motion is to be generated, the Male and Female are always join'd. [5] For example, a female high-density D-subminiature connector with a size 1 shell can be named DE15F or DE15S (see accompanying pictures). Both terms mean the same thing but could be construed to be completely different items. Similarly, a male standard-density D-sub with a size 1 shell can be named DE9M or DE9P; a female standard-density D-sub with a size 2 shell can be named DA15F or DA15S; a male high-density D-sub with a size 3 shell can be named DB44M or DB44P; and so forth. a b "Essential Connector Terms and Definitions for Specifiers of Interconnect Wiring Systems" (PDF). Glenair, Inc. 2004 . Retrieved 2019-06-25.

Downspouts (also called downpipes, rain conductors, or leaders) are used to convey rainwater from roof gutters to the ground through hollow pipes or tubes. These tubes usually come in sections, joined by inserting the male end (often crimped with a special tool to slightly reduce its size) into the female end of the next section. These connections are usually not sealed or caulked, instead relying on gravity to move the rainwater from the male end and into the receiving female connection located directly below. In computing, electrical connectors are considered a physical interface and constitute part of the physical layer in the OSI model of networking. The assignment is a direct analogy with male and female genitalia, the part bearing one or more protrusions or which fits inside the other being designated male, in contrast to the part containing the corresponding indentations, or fitting outside the other, being designated female. Extension of the analogy results in the verb to mate being used to describe the process of connecting two corresponding parts together.

KEY FEATURES OF JST RCY 2-PIN MALE/FEMALE CONNECTOR:

a b c "Connectors: Failure Mechanisms and Anomalies" (PDF). Naval Sea Systems Command . Retrieved 1 July 2019.