Bluelab MONGUA Guardian Monitor for pH, Temperature, and Conductivity Measures, Easy Calibration and Wall Mounted

Product Information

To select your desired conductivity unit, hold the unit button, located next to the conductivity display, down for 3 seconds. This process will trigger a move to the next unit of measurement, as indicated by the 3 LEDs to the right of the display. Repeat this process until you have arrived at your chosen unit of measurement. Repeat the whole process again for your choice of temperature measurement. Bluelab pH Probes: Care, maintenance and storage- Clean, hydrate and calibrate your pH probe monthly.

The Bluelab Guardian Monitor is a continuous indicator of the current levels of EC, pH and temperature of your nutrient solution, enabling you to optimise these parameters as your crop progresses through each growing phase. Features Before doing anything, you should soak the pH probe in KCL (potassium chloride) solution for 24 hours. This is very important! Read more on provisioning here. Why does the Bluelab Guardian reading start at 5 EC then drop down to the correct reading when you initially power it up?The Bluelab Guardian can be mounted in a suitable area, using the 4 supplied screws. Make sure that it is placed in an area that will allow the probes to reach the reservoir tank comfortably – no further than two meters away. Two cable ties are supplied with the unit, which can be used to mount it to a support or hanging bar. Avoid positioning the Guardian in areas of direct sunlight. Though the unit is water resistant, you should also avoid positioning it in areas where it can easily be splashed with nutrients. Mineral salt deposits can be corrosive and cause damage over long periods of time. Yes. A Bluelab Wi-Fi device can be reprovisioned onto a new Wi-Fi Network by entering “Provisioning Mode” on the device and using the Edenic phone app to configure the device. The Bluelab Guardian Monitor is mains-powered and is mounted to the wall or hung on a support and the probes simply placed into the pond water, filter.

Get your temperature, pH and CF right to boost nutrient uptake, enhance growth and improve root health. The Bluelab Guardian monitors temperature in centigrade or Fahrenheit, conductivity in terms of EC / CF / TDS / ppm, and also pH levels – and it does it consistently and accurately, with the use of scientific grade external probes. The Guardian will even provide a visual alert should levels drop below, or rise above, pre-programmed values – minor issues can then be dealt with before they become major issues. Growing hydroponically requires the careful monitoring of a few key nutrient parameters. The values of these parameters can be the difference between a successful grow and a completely failed crop, such is their level of importance.

Can't find what you're looking for? We're here to help...

Fit the (optional) pH probe holder to the stem of the pH probe. Do not flex or bend the probe stem as it may break! With Edenic, manage your Guardian Monitor Wi-Fi from where you like, when you like. Control parameters, monitor your environment and learn from your data with custom reporting. Visit: www.edenic.io Probe maintenance: To set conductivity alarm high value, please press the conductivity ‘units’ button then the up and down buttons to change the value. So confident are Bluelab in this product's robustness, that every Guardian comes supplied with a two year guarantee. Only the pH probe is exempt, due to the delicate nature of its glass parts, yet even this still comes with a guarantee of 6 months.

Place the tip of both probes in Bluelab pH 4.0 Calibration Solution or pH 10.0 calibration solution. A. Press and hold conductivity ‘units’ button. After 3 seconds it will change to the next unit indicated by the glowing LED. Release button. Repeat step until desired unit is selected. Many plants flower as a result of changes in the number of hours of uninterrupted darkness they're exposed to. The display LEDs on the Guardian glow in a plant-safe green that won't disturb dark periods and cause unwanted issues.Press and hold the 'display brightness' button while pressing up or down buttons to change brightness. The reading settles after about 30 seconds so wait for a short while for EC to stabilise. Is the Bluelab pH Probe fully submersible? Choose the correct plug adapter from the supplied selection, connect it to the Guardian's power supply, then connect the power supply to the underside of the main unit. Attach the pH probe to the underside of the unit, by inserting and twisting. The temperature / conductivity probe is supplied pre-attached. The unit can now be powered up at the mains supply. The conductivity / temperature probe is supplied factory calibrated and will only require periodical cleaning. The pH probe, however, will need to be calibrated before use. Add a small amount of pH 7.0 calibration solution to a small beaker or plastic container, dip the end of the probe in the solution and hold the 'pH cal' button, located to the left of the pH read-out display. Rinse the probe tip and repeat the process with either pH 4.0 or pH 10.0 solution to provide a more accurate calibration.